|
Products |
|
 |
LN25 Voltage-Sensing Wirefeeder
For MIG and Flux-Cored Welding with 10-44 lb Wire Spools
Designed for .023-1/16" Solid, .035-5/64" Cored and .035-1/16" Aluminum
Wire Sizes
Operates from all Welders with CV Capability for Maximum Versatility and
Portability
Powered across-the-arc, so no control cables are required! Simply
connect the welding cable to a power source, attach a work clip and
you're ready to weld. Includes a voltmeter, gas solenoid, and an
internal contactor. Can be operated with all electric and engine-driven
welders with CV capability but can also be used with CC welders for
non-critical welds. Includes welding gun and cable assembly, as well as
a properly sized drive-roll kit. |
|
 |
Powermax 1000 Plasma
Cutter
3/4" Recommended Capacity, 1" Maximum Capacity, 1 1/4" Severance
Capacity
Powermax 1650 Plasma Cutter
1 1/4" Recommended Capacity, 1 1/2" Maximum Capacity, 1 3/4"
Severance Capacity
These air/plasma cutters provide best-in-class cutting power and feature
state-of-the-art, multi-voltage inverter
power supplies. Cut through mild steel, aluminum and most other metals
with new power and productivity. |
|
 |
SE1602W Smoke Extractor
Two Operating Speeds
Uses RSE200WF Reusable,Washable Filters
Stainless Steel Construction with Dual Bypass Motors
Filter can be blown out with air or washed and pre-coated. Includes
a 15' hose with magnetic locator. |
|
 |
DP225
Electric Power Distribution Panel
240, 380, 480 or 600 Volt Electric Power Distribution
8 - 60 Amp, 3 Phase Receptacles with 50 Amp Breakers
1 - 9 Connection Terminal Board with 20 Amp Breaker
1 - 225 Amp, 600 Volt Main Breaker
DP25 Powermate Step-Down Panel
460 or 600 Volt, Single Phase, 120/240 Volt Secondary
6 - 120 VAC Duplex Receptacles with 15 Amp GFI Breakers
2 - 240 VAC Twist-Lock Receptacles with 30 Amp GFI Breakers
1 - 20 Amp, 600 Volt Main Breaker
10 kVA 480/600 Volt to 120/240 Volt Step-Down Transformer
|
|
 |
Preston-Eastin 10 Ton Turning Roll Set
10 Tons (Per Driver/Idler Combination) Weight Capacity
30,000 lb Turning Capacity, 3,400 lb Tractive Pull
6" through 12' 0" Diameter Range, 1.5 to 45 IPM Speed Range
3/4 Horsepower Motor Size, 12" Rubber Wheel Diameter
Designed for precision alignment at any centre-distance setting. Rubber-tyred
rollers absorb shock during loading and cushion the load during welding.
Steel overload discs protect the rubber tyres from excessive overloads.A
remote-control pendant is included. |
|
 |
D300K3+3 Portable Diesel Welder
Stick Welding with Five Output Taps and Fine Current Control DC CC
Built to Red-D-Arc Extreme-Duty Specifications Fuel Efficient V1903
Kubota Diesel Engine 3,000 Watts AC Auxiliary Power
The pure DC generator with all copper coils provides excellent welding
characteristics.The weldor's choice for pipeline welding and general
construction work. Constant speed engine for instant arc starting. The
V1903 Kubota diesel engine provides reliable, efficient operation in
even the most severe conditions. |
|
 |
D500K5+3 Portable Diesel
Welder
Full Range Amperage Control and Job Selector (OCV) Control DC CC
Built to Red-D-Arc Extreme-Duty Specifications Fuel Efficient F-2803
Kubota Diesel Engine 3,000 Watts AC Auxiliary Power
For demanding jobs that call for high amperage capabilities using
electrodes up to 1/4" in diameter and air carbon arc (CAC-A) gouging
with carbons up to 5/16" in diameter. Precise control of both current
control and open circuit voltage for optimum arc characteristics.
|
 |
Mariner 5+3 Offshore
Diesel Welder
Offshore Environmental Protection Package DC CC Fuel Efficient F-2803
Kubota Diesel Engine
3,000 Watts AC Auxiliary Power
The ultimate offshore-environmental welding package.The protective
enclosure minimizes salt water intrusion and, with a built-in drip
reservoir, all engine fluids are contained in the event of an oil or
coolant leak. A lifetime pre-fuel separator protects the engine from
fuel-borne contaminants, and the engine is protected from hydrocarbon
over-running or explosion with an automatic over-run shut-down device. |
 |
MX350 Multi-Weld DC
Converter
For Onsite Multiple Stick and Wire Welding DC+ CC CV Operates from
Most Welders on 50 - 113 DC Volts Input A Single Welding Machine can
Power Several MX350 Multi-Welds 350 Amps, 34 Volts @ 100% Duty Cycle
Output per Unit
This system provides multioperator welding operation with a single
power-source, since each individual MX350 shares the DC current of a
single welder, whether electric-powered or engine-driven. Each
Multi-Weld can be used for positive polarity CC stick or CV MIG and
Flux-Cored wire welding. |
 |
E300 4Pak Multioperator
Welding System
Modular Pak Design DC CC DP120 Power Distribution Panel Included For
Stick Welding with up to 3/16" Diameter Electrodes
Ideal for shipyards, construction sites, or any job where operating
multiple arcs from a single primary power source is an advantage. Up to
250 DC amps per arc with continuous output control. Individual welding
modules permit easy access for service or repairs. Operates from a 120
amp service with either 460 VAC or 575 VAC three-phase input. |
|
 |
E500
4Pak Multioperator Welding System
Modular Pak Design
DC CC DP120 Power Distribution Panel Included
For High Amperage Stick Welding and Air Carbon Arc Gouging
All the benefits of the E300 Multioperator Pak System but with up to 625
amps DC from each module.
Each module has its own arc force control, potentiometer-type continuous
output control and remote control receptacle. Built to Red-D-Arc
Extreme-Duty specifications for dependable operation in even the
most severe conditions. Operates with either 460 VAC or 575 VAC
three-phase electrical input. |
 |
Mark VIII-2 Multioperator Welding System
Stick (SMAW) and DC TIG (GTAW) Welding
DC CC Air Cabon Arc Cutting and Gouging (CAC-A)
Flux-Cored (FCAW), MIG Welding with Voltage-Sensing Wirefeeders
This durable, heavy-duty multioperator welding system drives eight
modules from a single main transformer. Each welding module features
remote control capabilities, and a wide range of amperage settings.
There is also a 15 amp 115 VAC duplex receptacle to run grinders,
drills, coolers, etc. from the power source. |
 |
EX350i Inverter Multioperator Welding
System
Compact, Highly Portable Inverter Design DC CC CV
Variable Hot Start, Arc Force and Inductance (Pinch) Control
CC Soft, CC Crisp, CV Wire, CV Flux-Cored, TIG Welding Modes
Outstanding arc characteristics with both constant current and constant
voltage welding processes in a
rugged, compact design. Advanced Plug-and-Play control recognition with
Amphenol connections for
24C, 42V and 115V wirefeeders and connections for 3-pin Stick remote
controls. |
|
|
DC600 4Pak Multioperator Welding System
Modular Pak Design
Full Range Output Control, Standard Ammeter and Voltmeter
CC Stick, CV MIG/FCAW and CV Submerged Arc Welding Modes
All the power of a single DC600 multiprocess welder, in a 4Pak
multioperator package. Features both 42 VAC and 115 VAC auxiliary power
for operating a wide range of wirefeeders and tractors. Built to
Red-D-Arc Extreme-Duty specifications including a unique Pak-Lok
connection system. Each Pak operates on 460 VAC or 575 VAC three-phase
input power from a single power-supply. |
 |
Articulated & Telescopic Boom Lifts
Manlifts
|
 |
Electric Scissors Lifts
|
 |
Modular Aluminium Suspended Platforms
-
Capacity 1,320lbs
(600kg) or 2200lbs (1,000kg)
-
Platform Length 2m, 3m, 7m
|
 |
Lifting Systems
-
2,000lb Rack &
Pinion Material Hoist
-
1,000lb / 2,000lb Portable Hoist
|
 |
Air Compressor XAS 97JD / XAS 186JD c/w / Pneumatic
Breakers
-
75-90 lb Breakers
-
c/w Lubricators & 100' Hose
-
Capacity 185 cfm@ 120 p.s.i
-
Capacity 375 cfm@ 120 p.s.i
|
 |
Generators
|
 |
Electric Drills/Breakers
-
Rotary Hammer
-
Demolition Breakers
-
From 5lb - 44lb Breakers
|
 |
Hydraulic Power Pack complete with Breaker
- 20L Hydraulic Power Pack
- 12/25 kg Hydraulic Breaker
|
 |
Dewatering Pumps
4" & 6" Trash Pumps |
 |
Modular Light Towers
|
